Kipi Calculator BASEBOARD & TRIM ESTIMATOR by Kipi Calculator
🌐 Español

Baseboard Calculator

    Measure your walls

    door Length (subtract doors/windows) Height Area = Length × Height

    Diagram: what the measurements mean

    Run a tape around every wall getting baseboard — add them all up into one number.

    Door openings

    Each doorway skips about 3 ft of baseboard — we subtract it for you.

    Shoe molding?

    The little quarter-round at the floor line — hides gaps where the floor meets the base.

    Your trim list

    Waste allowance Starts at 0% — tap to add a cushion for miter cuts & mistakes.

    Buy this much baseboard

    –

    Net length
    –
    To buy
    –
    8-ft sticks
    –
    Shoe molding
    –

      💡 Pro field tips

        🧰 Tools you'll need

        Tap to check off as you load up.

        Est. project cost (optional)

        File this estimate under a job name or PO to track what to order. Leave blank to file under "General".

        How the math works

        Baseboard looks simple — trim around the bottom of the walls — but corners are where material quietly disappears. Every miter and cope eats inches, and doorways break runs into pieces you can't always reuse. Here's how the calculator turns your room into a shopping list.

        Linear feet of wall

        Baseboard follows every wall, minus the openings. You add up the walls you are trimming (a 12 × 14 room has a 52-ft perimeter) and enter that total; the calculator subtracts the doorways:

        Linear feet = Total wall length − (Doors × 3 ft)

        Our 12 × 14 room: 52 − (3 × 3) = 43 linear feet. Subtract openings first because a doorway doesn't just skip material — it breaks the run, which changes how you plan pieces.

        Sticks: the buy count

        The calculator turns your buy length into 8-ft sticks — the most common trim length on the rack:

        Sticks = Buy length ÷ 8, rounded UP

        Buying longer stock instead (12 or 16 ft)? Divide the same buy length by that length — longer boards mean fewer joints on long walls but are harder to haul.

        Corners and miters

        Every corner consumes a little material beyond the measured wall:

        • Outside corners need two 45° miters — each piece loses ~3–4 inches past the corner point.
        • Inside corners are best coped (one board cut to match the other's profile) — about 2–3 inches per joint.

        This calculator does not add a per-corner charge — corner loss is exactly what the waste percentage below is for. Add it and the buy length grows to cover the corner cuts.

        Waste factor

        Add 10%: a miscut on a long board can ruin the whole board, since trim can't be spliced invisibly like flooring. The calculator starts at 0% — the exact footage — and the waste chips add your cushion:

        Buy length = Net linear feet × (1 + waste %)

        Worked example: 12 × 14 room, three doors

        • Linear feet: 52 − 9 = 43 ft
        • With 10% waste added: 43 × 1.10 = 47.3 ft to buy
        • Sticks: 47.3 ÷ 8 = 5.91 → buy 6 × 8-ft sticks

        That cushion feels like a lot — until one bad miter sends you back to the store.

        Most Asked Questions

        How much baseboard do I need for a 12 × 14 room?

        43 linear feet of trim for a typical 12 × 14 room with three doors. The room's walls add up to 52 ft, and the calculator subtracts 3 ft for each doorway: 52 − 9 = 43 ft. That's the exact buy at 0% waste — 6 × 8-ft sticks — and 47.3 ft with 10% added (still 6 sticks).

        How does the calculator handle doorways?

        It subtracts 3 ft per door opening — about what a standard doorway skips. Enter the number of doorways on the first step and the deduction comes off before waste, so you're not buying trim for wall that isn't there. For an extra-wide cased opening, count it as two doorways to stay close.

        Does the calculator add anything for miter cuts and mistakes?

        Not unless you tap it — waste starts at 0%, the exact footage. Outside corners lose about 3–4 inches per piece past the corner point and coped inside corners about 2–3 inches, so the chips (5–20%) are there when you want the cushion: the 43-ft room becomes 47.3 ft at 10%. The result notice always states whether no waste was added or the exact percentage included.

        How many sticks should I buy?

        The calculator divides your buy length by 8 and rounds up — the most common trim length on the rack. 47.3 ft ÷ 8 = 5.91, so buy 6 × 8-ft sticks. Buying 12- or 16-ft stock instead? Divide the same buy length by that length — longer boards mean fewer joints on long walls.

        Is shoe molding figured too?

        Yes — it's on by default, figured at the same buy length as the baseboard. 47.3 ft of baseboard at 10% waste means 47.3 ft of shoe molding too. Turn it off on the Details step if your baseboard sits tight to the floor without it.

        Can it estimate the project cost?

        Yes — enter a price per foot plus your labor and it totals both. Materials are figured on the full buy footage (baseboard plus shoe molding) times your price per foot; add labor hours × your rate for the project total.

        Next calculation

        One job usually leads to the next number. Common next steps from here:

        Embed this calculator on your site

        Run a DIY, contractor, or supplier site? Put this baseboard calculator right on your page, free. Copy the code and paste it where you want it — your visitors get the numbers without leaving your site.

        Free to use. The small “Powered by Kipi Calculator” line at the bottom of the calculator stays on — that’s all we ask.