Kipi Calculator CARPET ESTIMATOR by Kipi Calculator
🌐 Español

Carpet Calculator

    How big is the room?

    door Length (subtract doors/windows) Height Area = Length × Height

    Diagram: what the measurements mean

    Wall to wall, the longest runs — carpet gets cut to fit.

    Measure the two longest walls — the roll has to cover the full run.

    Pick your carpet style

    The math is the same either way — this just labels your estimate.

    Your carpet order

    Waste allowance Starts at 0% — tap to add a percentage for seams & pattern matching if you want one.

    Order this much

    – sq yd

    Exact yardage
    –
    To order
    –
    Carpet pad
    –
    Tack strip
    –

      💡 Pro field tips

        🧰 Tools you'll need

        Tap to check off as you load up.

        Est. project cost (optional)

        File this estimate under a job name or PO to track what to order. Leave blank to file under "General".

        How the math works

        Carpet is priced by the square yard, and this calculator works in area from start to finish: measure the room, convert to square yards, round the order up to the nearest tenth, and figure pad and tack strips from the same numbers. No roll-cut math — the square-yard order is what the store cuts from whatever roll width they stock.

        Room area to square yards

        Carpet covers area, so start with the floor itself:

        Square yards = (Length × Width) ÷ 9

        A 16 × 14 room is 224 sq ft, and 224 ÷ 9 = 24.89 sq yd. For L-shaped rooms, measure each rectangle separately, add the square feet together, then divide by 9.

        Rounding the order up to the nearest tenth

        Stores sell carpet by the tenth of a square yard, so the exact figure always rounds UP — never down, never to the nearest:

        Order = exact square yards, rounded up to the nearest 0.1

        24.89 sq yd orders as 24.9 sq yd. That small round-up is the only extra built in — the waste percentage starts at 0%, and nothing more is added until you tap one of the waste buttons.

        Waste, when you add it

        Tap a waste percentage and it goes on the exact square yards before the round-up:

        Order with waste = (Exact sq yd × (1 + waste %)), rounded up to the nearest 0.1

        At 10%: 24.89 × 1.10 = 27.38 → order 27.4 sq yd. A little waste covers seams, trimming into out-of-square walls and pattern matching; the result notice always states the exact percentage included, or that none was added.

        Padding and tack strips

        Pad is figured at the same amount as the carpet order — waste and round-up included — so the pad never comes up short under a seam:

        Padding (sq yd) = Carpet order (sq yd)

        Tack strips grip the carpet around the full perimeter of the room:

        Tack strips (ft) = 2 × (Length + Width)

        For the 16 × 14 room that's 2 × 30 = 60 ft. The calculator figures the full perimeter with nothing subtracted for doorways — a doorway still gets tack across it in most installs, and the extra few feet cost little.

        Worked example: 16 × 14 room

        • Area: 16 × 14 = 224 sq ft
        • Square yards: 224 ÷ 9 = 24.89 sq yd
        • Order at 0% waste: round up to the nearest tenth → 24.9 sq yd (27.4 sq yd with 10% waste added)
        • Padding: same as the carpet → 24.9 sq yd
        • Tack strips: 2 × (16 + 14) = 60 ft

        One honest note: this is an area figure. If your room is wider than the roll your store stocks — most rolls are 12 or 15 ft — the installer will seam two pieces, and seams waste a bit more in practice. That's what the waste buttons are for.

        Most Asked Questions

        How much carpet do I need for a 16 × 14 room?

        Order 24.9 sq yd — and the same 24.9 sq yd of pad. The room is 224 sq ft; 224 ÷ 9 = 24.89 sq yd exact, rounded up to the nearest tenth. Tack strips for the same room: 60 ft, the full perimeter.

        How do I convert square feet to square yards?

        Divide by 9. One square yard is 3 ft × 3 ft = 9 sq ft, so a 224 sq ft room is 24.89 sq yd. The calculator does the division for you and shows the exact figure before any rounding or waste.

        Why does the order round up to the nearest tenth?

        Because carpet is sold by the tenth of a square yard. 24.89 sq yd can't be bought as-is — the store cuts 24.9. Rounding up (never to the nearest) is the only rounding built into the number before you choose a waste percentage.

        Does the calculator add waste automatically?

        No — waste starts at 0%, and the result notice tells you. Tap a chip to add 5–20%: at 10% the 16 × 14 room goes from 24.9 to 27.4 sq yd, and the pad amount follows the carpet. Waste covers seams, out-of-square walls and pattern matching.

        How much tack strip do I need?

        The full perimeter of the room: 2 × (length + width). A 16 × 14 room takes 60 ft. Nothing is subtracted for doorways — most installs run tack across doorways too, and the extra few feet cost little.

        Does the carpet style change the amount?

        No — plush, berber and frieze all figure the same square yards. The style pick only names the carpet on your result, printout and saved estimate. The quantities come from the room size and the waste percentage, nothing else.

        Next calculation

        One job usually leads to the next number. Common next steps from here:

        Embed this calculator on your site

        Run a DIY, contractor, or supplier site? Put this carpet calculator right on your page, free. Copy the code and paste it where you want it — your visitors get the numbers without leaving your site.

        Free to use. The small “Powered by Kipi Calculator” line at the bottom of the calculator stays on — that’s all we ask.