Kipi Calculator CONCRETE BLOCK COUNTER by Kipi Calculator
🌐 Español

Concrete Block Calculator

    Which block are you buying?

    Pick the block size — thickness is about strength, not count.

    All four sizes share the same 8×16 face, so the block count comes out identical — thickness changes strength and insulation, not the count. Pick the one you're actually buying so the order list is right.

    How big is the wall?

    Length × height — then subtract the holes.

    Total area of the doors and windows in this wall. A standard door is about 21 sq ft, a typical window about 15 sq ft. Leave at 0 if there are none.

    Your block order

    Waste allowance Starts at 0% — tap to add a cushion for cuts & breakage.

    Order this many blocks

    – blocks

    Blocks (exact)
    –
    Mortar — 80-lb bags
    –
    Net wall area
    –
    Courses
    –

      💡 Pro field tips

        🧰 Tools you'll need

        Tap to check off as you load up.

        Est. project cost (optional)

        File this estimate under a job name or PO to track what to order. Leave blank to file under "General".

        Assumptions & limits: Block sizes are nominal — a block sold as 8×16 actually measures 7⅝ × 15⅝ in, and the math assumes standard 3/8-in mortar joints, which is why each block covers 0.889 sq ft of wall. Openings are subtracted at the area you enter — leave them out and the count runs high. Mortar is figured at about 30 blocks per 80-lb bag of pre-mixed mortar mix, the standard estimating rate for face-shell bedding (about 3 bags per 100 blocks); Quikrete's published yield for an 80-lb bag is up to 13 blocks at full bedding, so solid-bedded or structural work will need more. This calculator covers block and mortar counts only — structural walls also need rebar, grout-filled cores, and a proper footing per local code. Check your local code before building foundations or load-bearing walls.

        Estimates for planning only — confirm final quantities with your supplier and follow local building code.

        How the math works

        Block walls look simple — stack, mortar, repeat — but the count trips people up because a block is not the size it says on the tag. Here's the whole calculation, including the one number (1.125) that runs everything.

        Blocks per square foot: the 1.125 rule

        A standard block is sold as 8×8×16 inches, but it actually measures 7⅝ high × 15⅝ long. The missing ⅜ inch is the mortar joint. So on the wall, one block plus its joint covers exactly 16 × 8 = 128 square inches:

        128 in² ÷ 144 = 0.889 ft² per block → 1 ÷ 0.889 = 1.125 blocks per square foot

        Every standard-face block — 4, 6, 8 or 12 inches thick — uses the same 1.125. Thickness changes the wall's strength, not the count.

        Wall area, minus the holes

        Net area = (Length × Height) − Openings

        A standard door is about 21 sq ft and a typical window about 15. Skip the subtraction on a wall with two doors and three windows and you've ordered roughly 100 blocks too many — a full pallet of mistake.

        The 10% waste buffer

        Ends and corners need cuts, and blocks chip and crack in transit and on the saw. Ten percent covers normal cuts and breakage on a straight wall; go higher for lots of corners or openings. Running short mid-wall costs a second delivery — the buffer is cheaper.

        Mortar: about 30 blocks a bag

        Pre-mixed mortar in 80-lb bags is figured at roughly 30 blocks per bag with standard face-shell bedding — about 3 bags per 100 blocks. Manufacturers rate a bag lower (Quikrete's published yield is up to 13 blocks at full bedding), so if you're bedding every shell solid, order more. And no, this calculator doesn't count grout or rebar — structural walls need both, sized by code, not by a web form.

        Worked example: 20 × 8 wall, no openings

        • Area: 20 × 8 = 160 ft²
        • Blocks: 160 × 1.125 = 180 exact
        • With 10% waste: 180 × 1.10 = 198 to order
        • Mortar: 198 ÷ 30 ≈ 7 bags (80-lb)
        • Courses: 8 ft ÷ 8 in per course = 12 courses

        About two pallets of block and seven bags of mortar, and you're building by lunch.

        Worked example

        A 30 × 8 ft block wall — say a workshop wall — with one 3×7 door (21 ft²) and one 3×5 window (15 ft²), in standard 8×8×16 block:

        • Gross area: 30 × 8 = 240 ft²
        • Minus the openings: 240 − 21 − 15 = 204 ft² of actual wall
        • Blocks: 204 × 1.125 = 229.5 — call it 230 exact
        • With the 10% waste buffer: about 253 blocks to order
        • Courses: 8 ft ÷ 8 in per course = 12 courses
        • Mortar: 253 ÷ 30 blocks per 80-lb bag ≈ 9 bags of premix

        Skip the opening subtraction on this wall and you'd have ordered about 40 blocks too many — and still needed the same 9 bags.

        On a real job

        • The first course is the wall. Every course above inherits its level and its mistakes. Take the extra twenty minutes with the level and line on course one — it pays back on all eleven above it.
        • Run a true running bond. Joints stagger half a block (8 inches) course to course. Stacked joints line up into a crack with a zip code.
        • Mix mortar in small batches in hot weather. Mortar that has sat too long gets retempered with water again and again — and loses strength every time. Toss what's dead; a bag is cheaper than a weak wall.
        • Keep block dry and off the ground. Block wicks water like a sponge, and a wet block lays and bonds differently than a dry one. Store pallets on planks, covered, until they go in the wall.
        • Long walls need control joints. Block walls shrink slightly as they cure; on long runs, a tooled or sawn joint about every 25 ft (and where the engineer calls for them on structural work) decides where the wall moves.

        Most Asked Questions

        How many concrete blocks do I need for 100 square feet?

        113 blocks exactly. 100 sq ft × 1.125 blocks per sq ft = 112.5, rounded up. This calculator starts at 0% waste — tap the 10% chip for cuts and breakage and the order becomes 124.

        How many blocks do I need for a 20×8 wall?

        180 blocks exact — 198 with the 10% waste chip tapped. A 20 × 8 wall is 160 sq ft × 1.125, stands 12 courses high, and takes about 7 bags of mortar at the 198 count.

        How much mortar do I need for my blocks?

        About one 80-lb bag of pre-mixed mortar per 30 blocks, rounded up. That's the rate this calculator uses — a 180-block wall figures 6 bags. Bedding every shell solid uses more: manufacturers rate a bag as low as 13 blocks at full bedding.

        Does block thickness change how many blocks I need?

        No — 4, 6, 8 and 12-inch block all count the same. Every size has the same 8×16 face, so each block covers 0.889 sq ft with its mortar joint. Thickness changes the wall's strength, not the count.

        How many blocks come on a pallet?

        Usually about 90–120 standard 8×8×16 blocks, but it varies by size and supplier. Ask your yard when you order — pallet pricing and delivery usually beat loose blocks and pickup trips.

        Is a cinder block the same as a concrete block?

        Yes — it's the same product with an older name. Old blocks were made with coal cinders in the mix; modern blocks (CMU, concrete masonry units) are cast from concrete, but the name stuck.

        Next calculation

        One job usually leads to the next number. Common next steps from here:

        Embed this calculator on your site

        Run a DIY, contractor, or supplier site? Put this concrete block calculator right on your page, free. Copy the code and paste it where you want it — your visitors get the numbers without leaving your site.

        Free to use. The small “Powered by Kipi Calculator” line at the bottom of the calculator stays on — that’s all we ask.

        Popular lookups

        10×8 wall · 20×8 wall · 30×8 wall · 40×8 wall · 50×8 wall · All charts