Kipi Calculator PIPE SLOPE GUIDE by Kipi Calculator 🌐 Español

Pipe Slope & Fall, Figured Out

Every drain and sewer job is one question said three ways: how steep is the line, and how far does it drop from here to there? Plans say it in percent, plumbers say it in inches per foot, and the trench feels it as total fall. Here's how the three languages translate — and the minimums that keep a line working.

The three ways slope gets said

Slope percent is feet of fall per 100 feet of run. A 1% line drops 1 ft in 100 ft — 0.10 ft in every 10 ft. This is the language of site plans and of both calculators on this page.

Inches per foot is the plumber's language: ¼ inch per foot, ⅛ inch per foot. It's the same slope in smaller bites. Convert with inches per foot = slope % × 12 ÷ 100. So 1% = 0.12 in/ft (call it ⅛), and ¼ in/ft = 2.08%.

Total fall is the elevation you actually lose from one end of the run to the other: total fall = run × slope % ÷ 100. Total fall is what turns a start invert into an end invert — the number the whole job is built around.

Slope %Inches per footFall per 10 ft
0.50%0.06 in/ft (about 1/16)0.05 ft
1.00%0.12 in/ft (about ⅛)0.10 ft
1.04%⅛ in/ft0.104 ft
2.08%¼ in/ft0.21 ft
4.17%½ in/ft0.42 ft
8.33%1 in/ft0.83 ft

Minimum slopes by pipe size

A sewer has to move solids, not just water, so smaller pipe needs more slope to keep things moving. These are the planning minimums the sewer calculator uses — your local code and your project plans govern, and they can require more:

Pipe sizeMinimum slopeSame slope as
4 in2.08%¼ in per foot
6 in1.04%⅛ in per foot
8 in0.40%—
10 in0.28%—
12 in0.22%—
15 in0.15%—

Storm drain is more forgiving — it carries water and grit, not solids — and 0.5% is the usual minimum, with 1% or steeper preferred so sediment flushes through instead of settling.

Worked example: 60 feet of 6-inch building sewer

Run your own numbers in the Sewer Line Calculator and the grade table will lay out every station for you.

Holding the slope in the trench

One warning: percent is not degrees

A 1% slope is not a 1-degree slope. One percent is about 0.57 degrees — and a true 1-degree slope is roughly 1.75%, which on a sewer run is the difference between the right fall and nearly double it. If a spec, a saw, or a phone app is talking degrees, convert before you dig: slope % = tan(degrees) × 100.

Frequently asked questions

How much fall does a sewer line need over 60 feet?

At the usual minimum for 6-inch pipe (⅛ inch per foot, 1.04%), a 60-ft run needs 0.62 ft of fall — about 7½ inches. At ¼ inch per foot it needs 15 inches. The right number depends on pipe size and your local code.

What is the difference between slope percent and inches per foot?

They are the same slope in different units. Percent is feet of fall per 100 feet of run; inches per foot is the fall across a single foot. Convert with inches per foot = slope % × 12 ÷ 100, so 2.08% = ¼ inch per foot.

How much fall is 1% slope over 100 feet?

Exactly 1 foot. Percent means feet per hundred feet, so 1% drops 0.10 ft (about 1-3/16 inches) every 10 feet and a full foot over 100.

Can a drain line be too steep?

It can cause trouble. On very steep runs the water can outrun the solids it should carry, leaving them behind, and every extra percent is more trench to dig at the deep end. The specified slope exists for a reason — hit it and hold it rather than adding extra.

Estimates for planning only — confirm final quantities with your supplier and follow local building code.