Kipi Calculator PLUMBING FIXTURE ESTIMATOR by Kipi Calculator
🌐 Español

Plumbing Calculator

    What are you plumbing?

    Count every fixture getting water — the parts list builds itself.

    Bathroom sinks
    Kitchen sinks
    Toilets
    Tubs / showers
    Washing machine
    Hose bibs
    Dishwasher

    Each fixture gets the shutoffs, supply lines, and traps it needs — no guessing.

    Your parts list

    Stock up on

    –

    Supply lines
    –
    P-traps
    –
    Wax rings
    –
    Teflon tape
    –

      💡 Pro field tips

        🧰 Tools you'll need

        Tap to check off as you load up.

        Est. project cost (optional)

        File this estimate under a job name or PO to track what to order. Leave blank to file under "General".

        How the math works

        Planning the plumbing for a bathroom, kitchen, or whole house starts with a simple question: how many fixtures, and what does each one need? Every toilet, sink, shower, and appliance connects to the same three systems — water supply in, drain out, and a shutoff so you can service it. This calculator turns your fixture list into a complete material count: supply lines, shutoff valves, and drainage needs, so nothing gets forgotten behind the drywall.

        Step 1: Count every fixture

        The calculator starts with your fixture inventory — toilets, sinks, showers, tubs, dishwashers, washing machines, hose bibs. The list itself is the input — this calculator turns your fixture counts into the rough-in parts list below: supply lines, shutoff valves, P-traps, wax rings and tape. (Drain sizing is a separate code question: plumbers size drains from fixture-unit tables, and this tool does not figure drain sizes.)

        Step 2: Supply lines — two per fixture (usually)

        Sinks set the pattern: the calculator counts 2 supply lines per sink (hot and cold). Toilets, the dishwasher and the hose bibs count 1 line each, and a washing machine counts 2. A tub or shower adds a P-trap to the list below but no supply lines in this count. A hall bathroom with a toilet, a sink, and a tub needs 1 + 2 = 3 supply lines. This count drives how many stub-outs the plumber roughs in and how many flexible connector hoses you buy at finish.

        Step 3: Shutoff valves at every fixture

        Code and common sense both say every fixture gets its own shutoff valve — usually one per supply line. The formula is simple: shutoff valves = total supply lines. That hall bathroom needs 3 shutoffs. Skipping them saves a few dollars per valve but means shutting off the whole house to fix one dripping faucet. The calculator includes them because any plumber will insist on them.

        Step 4: Drains and vents — general guidance (not figured by this tool)

        Drain pipe size follows the fixture-unit total: up to about 6 units can share a 2-inch drain, larger groups step up to 3-inch, and a whole-house main is typically 4-inch. Vents follow the same logic — every trap needs a vent so draining water does not siphon the trap dry (which is what lets sewer gas into the house). That sizing comes from your local code’s fixture-unit tables and your plumber’s layout — this calculator does not output a drain size, so treat the guidance above as background, not as a result from the tool.

        Step 5: A waste cushion on materials

        Pipe is counted exact — add your own 10% cushion for cuts and fitting takeoffs when you order — every elbow and tee "eats" a little pipe length where it inserts. Valves and connectors are counted exactly, since they are one-per-fixture items with no cutting involved.

        Worked example

        A hall bathroom: toilet (cold only), sink (hot + cold), tub/shower (trap only in this count). Supply lines: 1 + 2 = 3. Shutoff valves: 3. P-traps: 2 (sink + tub). Wax rings: 1. Teflon tape: 1 roll. That is the complete rough-in shopping list this calculator gives for one bathroom, from three fixture counts. (Drain size is not part of the list — sizing drains from fixture units is general plumbing guidance, covered in Step 4, not an output of this tool.)

        Most Asked Questions

        What parts does one hall bathroom need?

        3 supply lines, 3 shutoff valves, 2 P-traps, 1 wax ring, and 1 roll of Teflon tape. That is a toilet (cold line only), a sink (hot and cold), and a tub/shower (a trap, but no supply lines in this count): lines 1 + 2 = 3, a shutoff for each line, traps for the sink and the tub, and one wax ring under the toilet.

        How many supply lines does each fixture get?

        Sinks get 2 — hot and cold. Toilets, the dishwasher and hose bibs get 1 each, and a washing machine gets 2. Those are the braided supply lines the calculator counts. A tub or shower adds a P-trap to the list but no braided line in this count. A hose bib counts 1 line — it is fed by a supply line like any other fixture, and it gets its shutoff valve from that same count.

        How many shutoff valves do I need?

        One for every supply line. The valve count uses the exact same per-fixture pattern as the lines (sinks × 2, toilets × 1, dishwasher × 1, washer × 2, hose bibs × 1), so the valve count and the line count come out equal — every supply line gets its own shutoff, hose bibs included. Skipping shutoffs saves a few dollars per valve but means shutting off the whole house to fix one dripping faucet.

        How are P-traps and wax rings counted?

        P-traps: 1 per sink plus 1 per tub or shower. Wax rings: exactly 1 per toilet. Both are exact one-per-fixture counts with no rounding and no hidden extra — a 2-sink, 1-tub bathroom takes 3 traps, and a 2-toilet house takes 2 wax rings.

        How much Teflon tape do I need?

        1 roll for every 4 fixtures, rounded up. The calculator divides your total fixture count by 4 and rounds up: the 3-fixture hall bathroom takes 1 roll, and a 9-fixture house takes 3. Tape is cheap insurance — running out mid-job costs a store trip, not a calculation.

        Does this calculator size my drain pipes?

        No — it counts parts, not drain sizes. Drain sizing comes from your local code's fixture-unit tables and your plumber's layout: as general guidance, up to about 6 fixture units can share a 2-inch drain, larger groups step up to 3-inch, and a whole-house main is typically 4-inch. Treat that as background, not as a result from this tool.

        Next calculation

        One job usually leads to the next number. Common next steps from here:

        Embed this calculator on your site

        Run a DIY, contractor, or supplier site? Put this plumbing calculator right on your page, free. Copy the code and paste it where you want it — your visitors get the numbers without leaving your site.

        Free to use. The small “Powered by Kipi Calculator” line at the bottom of the calculator stays on — that’s all we ask.