Kipi Calculator BOARD FOOT CALCULATOR by Kipi Calculator
🌐 Español

Board Foot Calculator

    What size boards?

    Pick a common size — it fills in the thickness and width. You can adjust everything next.

    Board details

    Thickness and width in inches, length in feet, and how many boards.

    Thickness:

    Add it and we'll figure the total lumber cost too. Fractions work in the size boxes — try 8' 6" for length or 1 1/2 for thickness.

    Your lumber count

    Total board feet

    – board ft

    Per board
    –
    Linear feet
    –
    With 10% waste
    –
    With 15% waste
    –

      💡 Pro field tips

        🧰 Tools you'll need

        Tap to check off as you load up.

        Est. project cost (optional)

        File this estimate under a job name or PO to track what to order. Leave blank to file under "General".

        Assumptions & limits: Board feet are figured from the dimensions you enter. Lumber is sold by nominal size — a "2×4" actually measures 1.5 × 3.5 in — and many yards bill board feet on the nominal size, not the actual wood. For an exact count of the wood itself (rough lumber, or milling your own), enter the actual measured dimensions instead. Add 10–15% for waste, defects, and cut-offs on rough lumber. Prices per board foot swing a lot with species, grade, and thickness — hardwood dealers price by the board foot, while big-box dimensional lumber is usually priced per piece.

        How the math works

        A board foot is a unit of wood volume: 144 cubic inches — picture a board 1 inch thick, 12 inches wide, and 1 foot long. Every board-foot count is just measuring your board against that block.

        The board foot formula

        Multiply thickness (inches) by width (inches) by length (feet), then divide by 12:

        Board feet = Thickness (in) × Width (in) × Length (ft) ÷ 12

        If your length is in inches instead, divide by 144: BF = T × W × L (in) ÷ 144. Multiply by the number of boards for the total, and multiply the length by the quantity for total linear feet.

        Nominal vs. actual sizes — read this before you order

        Lumber is named by its nominal size: the size of the rough board before it was dried and planed smooth. A 2×4 starts near 2 × 4 inches and finishes at 1.5 × 3.5 inches. Same story down the rack: a 1×6 is really 0.75 × 5.5, a 2×6 is 1.5 × 5.5, a 2×12 is 1.5 × 11.25.

        Most lumber yards bill framing lumber by the nominal board foot, so the nominal numbers give you the count on the invoice. But if you're figuring the actual wood in a stack of rough lumber — or milling your own — enter the actual measured dimensions for exact counts. A nominal 2×4×8 holds 5.33 board feet on paper; the finished board in your hand is 3.5 board feet of actual wood.

        Waste: add 10–15%

        Rough lumber has knots, checks, warped boards, and ends you'll cut off. Add 10% for straight, clean stock and 15% or more for rough, rustic, or figured lumber where you'll cull boards and match grain.

        Worked example: ten 2×6 boards, 8 ft long

        • Per board: 2 × 6 × 8 ÷ 12 = 8 board feet
        • Total: 8 × 10 boards = 80 board feet
        • Linear feet: 8 ft × 10 = 80 linear ft
        • With 15% waste: 80 × 1.15 = 92 board feet to order

        Framing a wall with those boards? The Stud Calculator counts the studs, and the Plywood Calculator figures the sheathing to cover them.

        Most Asked Questions

        How many board feet are in a 2×4×8?

        5.33 board feet at the nominal size. 2 × 4 × 8 ÷ 12 = 5.33. The finished board actually measures 1.5 × 3.5 in, which is 3.5 board feet of actual wood — yards usually bill the nominal number.

        What is a board foot?

        A board foot is 144 cubic inches of wood. Picture a board 1 inch thick, 12 inches wide, and 1 foot long. It is how lumber yards price and tally lumber, especially hardwoods and rough stock. The formula: thickness (in) × width (in) × length (ft) ÷ 12.

        Why is a 2×4 not 2 inches by 4 inches?

        The name is the nominal size — the rough-sawn dimension before drying and planing. A 2×4 is cut close to 2 × 4 in green, then shrinks as it dries and is planed smooth on all four sides, finishing at 1.5 × 3.5 in.

        How much extra lumber should I add for waste?

        Add 10% for clean, straight stock with simple cuts. Add 15% or more for rough lumber, rustic or figured wood, and projects with lots of short cuts — you'll cull warped boards and lose length to cut-offs and defects.

        How is hardwood priced by the board foot?

        Total cost = total board feet × price per board foot. Hardwood dealers tally the board feet in each board and multiply by a price per board foot that depends on the species, grade, and thickness (sold as 4/4, 5/4, 8/4, and so on). Enter your dealer's price in the calculator and it figures the total for you.

        How many board feet are in ten 2×6 boards, 8 ft long?

        80 board feet — and 80 linear feet. Each board is 2 × 6 × 8 ÷ 12 = 8 board feet, so 10 boards make 80. The calculator also shows the order figures with waste added: 88 board feet at +10% and 92 at +15%, so you can pick the cushion that fits your stock.

        Next calculation

        One job usually leads to the next number. Common next steps from here:

        Embed this calculator on your site

        Run a DIY, contractor, or supplier site? Put this board foot calculator right on your page, free. Copy the code and paste it where you want it — your visitors get the numbers without leaving your site.

        Free to use. The small “Powered by Kipi Calculator” line at the bottom of the calculator stays on — that’s all we ask.