Framing & Lumber Calculators
Framing math is mostly counting — but counting wrong means a second lumber run, or a pile of boards you paid for and can’t use. Spacing, the extra stud for the end of the run, plates, openings: small details, real money.
Here you’ll find studs, joists, stairs, headers, plywood, and board feet. Each calculator walks through the count the way it’s figured on site, shows every step, and lets you add only the waste you choose.
Board Foot
Board feet per board and in total, linear feet, and lumber cost — from thickness, width, length, and quantity.
Open it →Header & Beam Sizer
Header size, jack studs, and king studs for any opening — load-bearing or not.
Open it →Joist & Rafter Counter
Floor joists, ceiling joists, and rafters — counts, buy lengths, and rim boards.
Open it →Plywood & 2×4 Estimator
4×8 sheets for any area plus 2×4 counts by length — sheathing, subfloor, and framing in one shot.
Open it →Stair Stringer
Rise, run, risers, treads, and stringers — with code checks so your stairs pass.
Open it →Stud Counter
Wall studs and plates — 2×4 or 2×6, 16" or 24" on-center, doors, windows, and corners, with the "+1" built in so you never come up short.
Open it →Deck Boards & Fasteners
Deck boards, joists, screws, and boxes for a deck that lays flat.
Open it →Framing is counting, in the right order
A framed wall or floor is a stack of repeated pieces, and the count for each piece depends on the decision before it. Spacing sets the stud and joist counts. The span sets the buy length. The openings set the headers that carry the load around them. Figure them out of order and you will either make a second lumber run or stand in the aisle doing math on your phone while the crew waits.
The calculators here follow the order a framer actually works: layout first, then the members that run across, then the openings and stairs, then the sheet goods that close it all in. Each one shows every step of its count — including the extra stud at the end of the run, the one everybody forgets exactly once and never again.
How a framing job flows
Walls, floors, openings, stairs, sheets:
- Lay out the walls — Stud Counter. Studs and plates at 16- or 24-inch on-center, with doors, windows and corners figured in and the +1 end stud built in, so the count matches the wall instead of just the division.
- Frame the floors and ceilings — Joist & Rafter Counter. Counts for floor joists, ceiling joists and rafters, the buy lengths the span needs, and the rim boards that close the edges.
- Carry the openings — Header & Beam Sizer. Header size plus the jack studs and king studs for every door and window opening — load-bearing or not.
- Build the stairs — Stair Stringer. Risers, treads and stringers from the total rise and run, checked against the stair limits so every step in the flight comes out the same.
- Sheet it and price the lumber — Plywood & 2×4 Estimator and Board Foot. 4×8 sheets for any area, plus board feet and cost when the yard sells the lumber by the board.
- Taking it outside? — Deck Boards & Fasteners. A deck runs its own count: boards, joists, screws and boxes for a deck that lays flat.
Most Asked Questions
Why is the stud count always one more than my math?
Because of the +1: spacing math counts the gaps, but the wall also needs a stud at the starting end. Then corners and openings add their own studs on top. The stud counter builds all of that in, so the number you order is the number the wall actually takes.
Should I frame at 16 or 24 inches on-center?
16 inches is the standard for load-bearing walls and most floors; 24 inches shows up in engineered layouts and some non-bearing walls. The load and your local code make the final call. The stud and joist counters here take either spacing, so you can run both counts and compare before you commit to one.
What makes a stair pass or fail?
Even steps, inside the limits. Code caps riser height at 7¾ inches and calls for treads about 11 inches deep — and every riser in the flight has to match, because the one step that is a quarter inch off is the one people trip on. The stair calculator splits the total rise evenly across the flight and checks the result against those limits.
What is a board foot, exactly?
A board foot is a volume: a piece of wood 1 inch thick, 12 inches wide and 12 inches long — 144 cubic inches. Yards price hardwood and rough-sawn lumber by it instead of by the piece. The board foot calculator figures board feet per board and in total from thickness, width, length and quantity, with linear feet and cost alongside.