Kipi Calculator EXCAVATION by Kipi Calculator

Excavation Calculators

Underground work is grade work. A pipe that falls the right number of tenths from box to box drains for decades; one that’s flat or back-pitched is a callback waiting to happen. Out here the math is read in feet and tenths off the rod — and these tools speak that language.

Figure storm drain and sewer grades with station-by-station tables and minimum-slope checks by pipe size, curb and gutter yardage, French drains, and grade and slope for any run. Built for the way excavation crews actually call grades on site.

Curb & Gutter

Cubic yards of concrete for curb and gutter from the run length and profile — pan and curb dimensions, yards per 100 ft, and contraction joints.

Open it →

French Drain Calculator

Gravel, perforated pipe, and landscape fabric for a French drain trench — yards, tons, pipe sections, and fabric rolls with a waste allowance and cost estimates.

Open it →

Grade & Slope Calculator

Percent grade, angle, and slope ratio from rise and run or two elevations — plus the fall you need over a run at a target grade, for driveways, ramps, yard drainage and site grading.

Open it →

Sewer Line Grade

End invert, total fall, slope in percent and inches per foot, and bury depths for building sewers and mains — with minimum-slope checks by pipe size.

Open it →

Storm Drain Grade

End invert, total fall, and a station-by-station grade table for storm drain boxes and pipe runs — from your start elevation and slope.

Open it →

Grade is the whole job

Excavation math sounds simple — water runs downhill — right up until you are the one holding the rod. A sewer line that falls a quarter inch per foot will drain for decades. The same line laid dead flat silts up and backs up. The difference between the two is a few tenths of a foot over a hundred-foot run, which is why grades out here are called in feet and tenths off the rod instead of inches off a tape.

These tools are built around that reality. Pipe runs get checked against the minimum slope for the pipe size. Grades come with station-by-station tables you can call out box by box as the trench opens up. And everything reads in the tenths the rod shows. The work around the pipe — surface drainage, curb and gutter, final grade — is figured here too, in the same language.

How an excavation job flows

Grade first, then pipe, then the surface:

  1. Set the grade — Grade & Slope Calculator. Percent grade, angle and slope ratio from a rise and run or two elevations — plus the fall a run needs at a target grade. Every other number on the job answers to this one.
  2. Run the storm drain — Storm Drain Grade. Start invert and slope give the end invert, the total fall and a station-by-station grade table for the boxes and pipe runs.
  3. Run the sewer — Sewer Line Grade. End invert, total fall, slope in percent and inches per foot, and bury depths — checked against the minimum slope for your pipe size.
  4. Catch the surface water — French Drain Calculator. Gravel, perforated pipe and landscape fabric for the trench that collects what the grade sends it.
  5. Finish the street edge — Curb & Gutter. Cubic yards from the run length and profile, with yards per 100 feet and contraction joints for the pour.

Most Asked Questions

How much fall does a sewer line need?

Smaller pipe needs more slope. The usual planning minimums are ¼ inch per foot — 2.08% — for 4-inch pipe, and ⅛ inch per foot — 1.04% — for 6-inch. The sewer line calculator checks the slope you enter against the minimum for the pipe size you pick and flags it when you are under.

Why do crews call grades in tenths instead of inches?

Because the grade rod is marked in feet and tenths, and it is read all day. Tenths also divide cleanly for slope math: a 1% grade drops exactly one tenth in ten feet. Inches would leave you converting fractions on a tailgate in the middle of a trench.

What's an invert?

The invert is the elevation of the inside bottom of the pipe — the surface the water actually flows on. Grades are figured invert to invert, not from the top of the pipe or the bottom of the trench. Both pipe calculators here start from your start invert and carry the slope through to the end invert.

How deep will the pipe be buried?

Enter your ground or rim elevations and the sewer calculator reports bury depth along the run. That number drives the rest of the dig: how wide the trench has to be, how much spoil you are moving, and when the hole gets deep enough that trench safety becomes the first conversation of the day.

More calculator groups

Concrete & Masonry CalculatorsFraming & Lumber CalculatorsRoofing CalculatorsLandscaping & Yard CalculatorsElectrical CalculatorsHome Remodeling Calculators