Kipi Calculator ROOFING by Kipi Calculator

Roofing Calculators

A roof is measured in squares, pitch, and coverage — and every material on it, from shingles to metal panels to the gutters at the edge, keys off the same roof area and slope.

Start with the pitch if you don’t know it, then figure shingles, metal, or rubber roofing, and finish with gutters and downspouts. Each tool shows its math, so the number on the order matches the roof on the house.

EPDM Rubber Roof Calculator

Membrane square feet, sheets, bonding adhesive, seam tape and lap sealant for a flat rubber roof.

Open it →

Gutter & Downspout

Gutter footage, downspouts, elbows, and hangers — sized right for the eaves.

Open it →

Metal Roofing Calculator

Panels, panel cut length, ridge cap pieces and screws for a simple gable metal roof — from footprint and pitch.

Open it →

Roof Pitch Calculator

Find roof pitch from rise and run — get the x/12 pitch, angle in degrees, and rafter length instantly.

Open it →

Roof Shingles

Squares, bundles, pitch multipliers, ridge cap and starter — order the entire roof in one shot.

Open it →

One roof, two measurements

Every number on a roofing job comes off two measurements: the area of the roof surface and its pitch. Pitch is what turns the footprint — the only thing you can measure from the ground — into the real surface area up top. Area is what turns into squares, the unit every roofer and supplier orders in. Get those two right and everything else on the order, from bundles to ridge cap to the gutters at the edge, falls into line behind them.

The classic mistake is ordering off the floor plan of the house. On a steep roof the sloped surface is much bigger than the footprint under it, and the shortage shows up on the last slope, with the crew standing around. The tools here all start from pitch and true roof area, and every one shows its math — so the number on the order matches the roof that is actually up there.

How a roofing job flows

Pitch first, covering second, edges last:

  1. Find the pitch — Roof Pitch Calculator. Rise and run give you the x/12 pitch, the angle in degrees and the rafter length. Every other number on the roof keys off this one.
  2. Figure shingles — Roof Shingles. Squares, bundles, pitch multipliers, ridge cap and starter — the whole asphalt roof in one order.
  3. Or figure metal — Metal Roofing Calculator. Panels, panel cut length, ridge cap pieces and screws for a simple gable roof, from the footprint and the pitch.
  4. Flat roof? Figure the membrane — EPDM Rubber Roof Calculator. Membrane square feet, sheets, bonding adhesive, seam tape and lap sealant for a flat rubber roof.
  5. Finish the edges — Gutter & Downspout. Gutter footage, downspouts, elbows and hangers for the eaves — run it last so the gutter plan matches the roof you ordered.

Most Asked Questions

What is a roofing square?

One square is 100 square feet of roof surface. Roofers and suppliers talk in squares, not square feet, and standard shingles are packaged three bundles to a square. The shingle calculator divides your roof surface by 100 and figures the bundles from there.

Can I just measure the house footprint?

Only if the roof is flat — a pitched roof has more surface than the floor plan under it. The steeper the pitch, the bigger the difference. Find the pitch first; these calculators use it to turn the footprint into the true roof area before anything gets counted.

Which calculator do I use for a flat roof?

The EPDM rubber roof calculator. Flat and low-slope roofs drain too slowly for shingles, so they get covered in rubber membrane sheets instead. It figures membrane square feet, sheets, bonding adhesive, seam tape and lap sealant — the full material list for the system.

Are gutters figured from the roof area too?

No — gutters measure along the eaves, not up the slope. The gutter calculator works from your eave lengths and figures gutter footage, downspouts, elbows and hangers. Run it after the roof covering so the edges finish the same roof the order was built for.

More calculator groups

Concrete & Masonry CalculatorsFraming & Lumber CalculatorsLandscaping & Yard CalculatorsElectrical CalculatorsHome Remodeling CalculatorsExcavation Calculators