Kipi Calculator DECK BOARD & FASTENER COUNTER by Kipi Calculator
🌐 Español

Deck Calculator

    What are you decking with?

    Both are 5½" wide — pick your board.

    How big is the deck?

    Length is the direction your boards will run.

    Boards are laid across the width with a ¼" gap; joists run every 16".

    Your deck count

    Waste allowance Starts at 0% — tap to add a cushion for cuts, culls & spares.

    BOARDS TO BUY

    –

    Boards
    –
    Board length
    –
    Joists (16" OC)
    –
    Screws
    –
    5-lb boxes
    –

      💡 Pro field tips

        🧰 Tools you'll need

        Tap to check off as you load up.

        Est. project cost (optional)

        File this estimate under a job name or PO to track what to order. Leave blank to file under "General".

        How the math works

        Deck math has two personalities: the framing underneath (the joists that carry everything) and the decking on top (the boards everyone sees and walks on). This calculator figures the decking package — boards, joists, screws, and boxes. Beams, posts, and footings are not figured by this calculator; they depend on your spans and local requirements, so they're figured separately. Decking is a coverage problem where the board gap is the sneaky variable.

        Decking boards

        Figure out how many boards it takes to cross the deck's width, then buy them at the deck's length. Boards = deck width in inches ÷ (board width + gap). A 12-foot-wide deck is 144 inches. With 5.5-inch boards and a 1/4-inch gap, each board effectively covers 5.75 inches: 144 ÷ 5.75 = 25.04, which rounds up to 26 boards, each 16 feet long (the deck's length). The gap is the part people forget — ignore it and 25 boards leaves you 6 inches short, because those quarter-inches add up across 25 boards. The gap is drainage plus room for swelling.

        Joists and spacing

        Joists run perpendicular to the decking, and this calculator figures them at 16 inches on-center — the same 16-inch logic as wall framing. Joists = (deck length in inches ÷ 16) + 1 — the joists run across the deck’s width, so each joist is as long as the deck is wide, and they are spaced along the length the boards run. A 16-foot-long, 12-foot-wide deck: 192 ÷ 16 = 12 spaces + 1 = 13 joists, each 12 ft long. (Composite decking flexes more and usually calls for 12 inches on-center on a real build — check your decking maker's spec; this tool's joist count uses 16".) Beams, posts, and footings are not figured by this calculator — they follow your span tables and local requirements.

        Board feet, for pricing the framing

        Lumberyards price framing lumber by the board foot: board feet = thickness (in) × width (in) × length (ft) ÷ 12. A 2×10×16 is 2 × 10 × 16 ÷ 12 = 26.7 board feet. It's the unit the price tag uses, so it's the unit your estimate should use.

        Fasteners and the waste factor

        Screws are two at every crossing: Screws = Boards × Joists × 2, and they come in 5-lb boxes of about 350, so Boxes = Screws ÷ 350, rounded up. The waste chips start at 0% and apply to the deck boards only — joists and screws are always figured on the exact layout, because you only screw down the boards you actually install. Cull decking hardest — a warped deck board is the one everyone sees.

        Worked example

        12 × 16 deck, 5.5" boards, waste at 0%: decking = 26 boards at 16 feet (144" ÷ 5.75" = 25.04, rounded up). Joists: 192 ÷ 16 + 1 = 13 joists (each 12 ft long, running across the width). Screws: 26 boards × 13 joists × 2 = 676 screws → 2 boxes (5-lb boxes of about 350). Beams, posts, and footings are not figured by this calculator. If you tap a waste chip, it raises the board count only — joists and screws stay on the exact layout.

        Most Asked Questions

        How many deck boards do I need for a 12 × 16 ft deck?

        26 boards, 16 ft long. Each board covers 5.75″ of the deck's width — the 5.5″ board plus its 1/4″ gap — so 144″ ÷ 5.75″ rounds up to 26 boards, bought at the deck's 16-ft board-run length.

        Does the board type change the count — 5/4×6 or 2×6?

        No — both figure the same coverage. Whichever you pick at step one, boards are counted at a 5.5″ face plus the 1/4″ gap, so the 12 × 16 deck takes 26 boards either way. Pick the decking you're actually buying — the count comes out the same.

        How many joists and screws does it figure?

        For that 12 × 16 deck: 13 joists and 676 screws — 2 boxes. Joists are figured at 16″ on-center, plus one to close the end. Screws are 2 per board at every joist crossing: 26 × 13 × 2 = 676, and screws come in 5-lb boxes of about 350.

        Does the waste percentage change the screws too?

        No — waste applies to the board count only. Tap 10% and the 12 × 16 deck goes from 26 boards to 29, but joists and screws stay figured on the exact layout. You only screw down the boards you actually install.

        Does it figure beams, posts, and footings?

        No — this one counts the decking package. Boards, joists, screws, and boxes. Beams, posts, and footings depend on your spans and local requirements, so they're figured separately — from a span table or your plan.

        What if my deck runs longer than 20 ft?

        Boards top out at 20 ft, and the tool flags the butt joint. Past a 20-ft board run it tells you to butt-joint two boards per run, and the length line updates to match.

        Next calculation

        One job usually leads to the next number. Common next steps from here:

        Embed this calculator on your site

        Run a DIY, contractor, or supplier site? Put this deck calculator right on your page, free. Copy the code and paste it where you want it — your visitors get the numbers without leaving your site.

        Free to use. The small “Powered by Kipi Calculator” line at the bottom of the calculator stays on — that’s all we ask.

        Popular lookups

        10×10 deck · 12×16 deck · 16×12 deck · 16×20 deck · 20×20 deck · All charts