Kipi Calculator STAIR STRINGER CALCULATOR by Kipi Calculator
🌐 Español

Stair Calculator

    Rise and run

    Rise (step height) Run Tread (where you step) Total rise ÷ 7" = steps

    Diagram: what the measurements mean

    Stairs are measured in inches — floor to floor, straight across.

    Floor surface to floor surface — the full vertical climb.

    How much horizontal space the stair gets.

    How wide is the stair?

    Wide stairs need a middle stringer so treads don't bounce.

    Your stair layout

    Cut this many risers

    –

      💡 Pro field tips

        🧰 Tools you'll need

        Tap to check off as you load up.

        Est. project cost (optional)

        File this estimate under a job name or PO to track what to order. Leave blank to file under "General".

        Assumptions & limits: Stair limits — maximum riser height and minimum tread depth — come from your local building code. A common standard (IRC) is a 7¾-inch maximum riser and 10-inch minimum tread, but your area may differ. Use this layout for planning and confirm it against local code before cutting stringers.

        How the math works

        A staircase is the same right triangle repeated until you reach the top. Get one step right and they all come out right; get the math wrong and every step is a tripping hazard. Everything hangs on one measurement and one famous rule.

        Total rise: the one measurement that matters

        Total rise is the vertical distance from the finished surface of the lower floor to the finished surface of the upper floor. Measure to the top of the tile, hardwood, or carpet actually going down — not the subfloor. A half-inch of forgotten flooring changes every riser height in the staircase.

        The 7-11 rule: comfort in two numbers

        Legs like a riser (vertical face) of about 7 inches and a tread (the part you step on) of about 11 inches. Code caps risers at 7¾ inches and demands treads at least 10 inches deep, but code is the legal minimum — 7 and 11 feels effortless. The deeper comfort formula: two risers + one tread = 24 to 25 inches. Seven and eleven gives 25 — right on the money.

        The formulas: dividing the rise

        Number of risers = Total rise ÷ 7, rounded to a whole number

        Actual riser height = Total rise ÷ Number of risers

        Tread depth = Total run ÷ Number of risers

        You enter the total run — the horizontal space the stair has to fit in — and the tool splits it evenly across the risers. (On a built stair the top landing serves as the last tread, but this tool works from the run you give it: tread depth is always your total run ÷ your risers.)

        Example: 98-inch total rise, 154-inch total run. 98 ÷ 7 = 14 → 14 risers; actual riser = 98 ÷ 14 = 7 inches exactly (under the 7¾ max). Tread depth = 154 ÷ 14 = 11 inches. Every step identical, because every riser and tread came from the same divisions.

        Stringers: the sawtooth backbone

        Stringers are the notched 2×12s running diagonally under the steps. The count comes from the width you pick at step two: 2 stringers for a stair up to 36" wide, 3 over 36" — both edges, plus a center one on wider stairs so treads don't flex. Each notch is one riser tall by one tread deep, laid out with a framing square. Code also demands 6'8" of headroom above every tread nosing — basement stairs fail inspections on headroom more than anything else.

        Worked example: 98" rise, 154" run

        • Risers: 98 ÷ 7 = 14 → 14 risers at 7" each
        • Treads: 154 ÷ 14 = 11" deep; total run 154"
        • Stringer length: √(98² + 154²) = 15.21 ft → buy 16-ft 2×12s
        • Stringers: 2 at up to 36" wide — 3 if you pick over 36" at step two
        • No waste is added — the counts come out exact. One miscut stringer ruins a whole 2×12, so a spare board is cheap insurance — but that's your call at the yard, not a number this tool adds.

        Cut one stringer, test-fit it, then use it as the template for the rest.

        Most Asked Questions

        How many risers does my stair need?

        Your total rise ÷ 7, rounded to a whole number. A 98″ rise gives 14 risers, and the tool splits the rise evenly: 98 ÷ 14 = an exact 7″ riser height on every step — no tall or short step anywhere.

        How deep will my treads be?

        Your total run ÷ the risers. The tool splits the run you enter evenly across the risers: a 154″ run over 14 risers gives 11″ treads, the comfortable standard. The tool checks riser height only — it stops you if a riser comes out over 7¾″ — so check the tread depth yourself: if the split comes out under 10″, add run or redesign before you build.

        How many stringers do I need?

        2 for a stair up to 36″ wide, 3 over 36″. Pick your width at step two. Wider stairs get the third 2×12 stringer in the middle so the treads don't flex.

        What length 2×12 should I buy for the stringers?

        The next stock length above the diagonal. The tool figures the stringer as the hypotenuse of your rise and run: √(98² + 154²) = 15.21 ft on the stair above, so you buy 16-ft 2×12s.

        Does the calculator check my stair against code?

        It checks the riser max for you. If the split puts a riser over 7¾″, the tool stops and tells you the stair won't pass as drawn — add run or redesign. It does not flag tread depth — confirm every tread is at least 10″ deep yourself before you build.

        Is there a waste percentage on the stairs calculator?

        No — this tool gives exact counts only. Risers, stringers, and board lengths come out as figured, with nothing added. If you want a spare stringer board against a miscut, that's your call at the yard.

        Next calculation

        One job usually leads to the next number. Common next steps from here:

        Embed this calculator on your site

        Run a DIY, contractor, or supplier site? Put this stair calculator right on your page, free. Copy the code and paste it where you want it — your visitors get the numbers without leaving your site.

        Free to use. The small “Powered by Kipi Calculator” line at the bottom of the calculator stays on — that’s all we ask.