French Drain Calculator
What pipe are you running?
Perforated pipe is the heart of the drain — pick your size.
Pick a pipe size to continue.
Size the trench
A typical house drain runs 12 inches wide and 18 inches deep — adjust to your job.
12 in is typical — room for pipe plus gravel on both sides.
18 in is typical — below the wet zone, above the frost trouble.
Measure the run where the water actually needs to go — from the wet area to where the drain daylights or ties in.
Waste allowance — extra for spills, over-dig & seam overlaps
Your drain materials
Order this much gravel
– yd³
Gravel fills the whole trench around the pipe, so the yardage uses the full trench volume. Weight uses the same 1.4 tons-per-yard figure as our gravel calculator. Pipe is figured in 10-ft sections; fabric rolls are figured at 3 ft × 50 ft (150 sq ft per roll).
- Est. weight
- –
- Pipe — 10-ft sections
- –
- Fabric rolls
- –
- Exact gravel
- –
💡 Pro field tips
🧰 Tools you'll need
Tap to check off as you load up.
Est. project cost (optional)
File this estimate under a job name or PO to track what to order. Leave blank to file under "General".
Copied to clipboard ✓
How the math works
A French drain is just a gravel-filled trench with a perforated pipe in the bottom: water seeps into the gravel, drops into the pipe, and the pipe carries it away. That means the shopping list is exactly three things — gravel, pipe, and the landscape fabric that wraps the trench and keeps dirt from silting it shut. Here's every assumption the calculator makes, out in the open.
Trench volume: length × width × depth
The trench is a box. Convert the width and depth from inches to feet (12 in = 1 ft, 18 in = 1.5 ft) and multiply:
Cubic feet = Length (ft) × Width (ft) × Depth (ft)
A 50-foot trench at the typical 12 inches wide and 18 inches deep is 50 × 1 × 1.5 = 75 cubic feet.
Gravel: the full trench, in yards and tons
Gravel fills the trench around the pipe, so the calculator orders the full trench volume — the pipe itself takes up so little room compared to the gravel bed that field practice just fills the trench. Convert to cubic yards:
Cubic yards = Cubic feet ÷ 27
75 ÷ 27 = 2.78 yd³. Gravel is also sold and hauled by weight, so the calculator converts with the same figure our gravel calculator uses:
Tons = Cubic yards × 1.4
Use washed drainage rock (¾-inch is typical) — the fines in crusher run pack tight and slow the water down.
Pipe: one run, in 10-ft sections
The perforated pipe runs the full length of the trench, so pipe length starts at the trench length. Rigid perforated pipe is sold in 10-foot sections, so the calculator rounds the waste-adjusted length up to whole sections:
Sections = Pipe length ÷ 10, rounded up
Four-inch perforated pipe is the residential standard; step up to 6-inch for long runs or heavy flow.
Fabric: the burrito wrap
The fabric lines the trench before the gravel goes in — down one side, across the bottom, and up the other side — then folds over the top like a burrito. Per foot of trench, the fabric has to span the trench width plus the depth twice:
Fabric per foot = Width + 2 × Depth
Fabric area = (Width + 2 × Depth) × Length
For the 50-foot trench: (1 + 2 × 1.5) × 50 = 4 × 50 = 200 sq ft. Rolls are figured at the common 3 ft × 50 ft roll = 150 sq ft per roll — check your roll's actual size when you buy; rolls are also sold 4 ft wide. This is non-woven drainage fabric (geotextile), not the plastic weed barrier from the garden aisle — weed barrier clogs and kills the drain.
Waste: the 10% rule
Over-digging, spilled gravel, cut pipe ends, and fabric seam overlaps all eat material. The calculator applies your waste percentage to the gravel, the pipe length, and the fabric before rounding up to whole sections and rolls:
Order quantity = Exact × 1.10 (at the 10% chip)
Worked example: a 50 ft trench, 12 in wide × 18 in deep
- Trench volume: 50 × 1 × 1.5 = 75 ft³ → 75 ÷ 27 = 2.78 yd³ of gravel (exact)
- With the 10% waste buffer: 2.78 × 1.10 = 3.06 yd³ to order — about 4.28 tons
- Pipe: 50 × 1.10 = 55 ft → 6 sections of 4-in perforated pipe
- Fabric: (1 + 3) × 50 = 200 sq ft × 1.10 = 220 sq ft → 2 rolls (3 × 50 ft)
One gravel delivery, six sticks of pipe, two rolls of fabric — the whole drain on one trip.
Worked example
You're drying out a 40 ft side yard with a 12 in × 18 in trench and 4-in pipe. Using this calculator's own math:
- Trench volume: 40 × 1 × 1.5 = 60 ft³ → 2.22 yd³ exact
- With waste: 2.22 × 1.10 = 2.45 yd³ to order (≈ 3.43 tons)
- Pipe: 40 × 1.10 = 44 ft → 5 sections
- Fabric: (1 + 3) × 40 = 160 sq ft × 1.10 = 176 sq ft → 2 rolls
Two rolls even though the math says 176 sq ft — fabric comes in whole rolls, and the leftover is cheap insurance for the seams.
On a real job
- Slope is everything. Pitch the trench about 1% toward the outlet — roughly 1 inch of fall every 8 feet. A flat French drain is just an underground pond; check the grade with a laser or string line as you dig.
- The drain needs somewhere to go. Daylight it on a slope, tie it into a dry well, or run it to a popup emitter well away from the foundation. Burying a pipe that ends in solid ground does nothing.
- Wrap the gravel, not just the pipe. Line the trench with fabric, add a gravel bed, set the pipe holes-down, fill with gravel, then fold the fabric over the top before backfilling. The wrap is what keeps silt out for decades.
- Washed rock only. Order washed ¾-inch drainage gravel. Crusher run and unwashed stone carry fines that migrate into the pipe and choke the drain from the inside.
- Call 811 before you dig. It's free, it's the law, and French drain routes love crossing the same ground as water lines and sprinkler runs. A couple of days' wait beats a repair bill.
- Add a cleanout at the high end. A vertical pipe with a cap at the start of the run costs almost nothing and lets you flush the line years from now without digging it up.
Most Asked Questions
How much gravel do I need for a 50-ft French drain?
2.78 cubic yards exact — about 3.89 tons. That's a trench 50 ft long, 12 in wide and 18 in deep: 50 × 1 × 1.5 = 75 ft³ ÷ 27 = 2.78 yd³, converted at 1.4 tons per yard. Tap the +10% chip and the order becomes 3.06 yd³, about 4.28 tons.
How much slope does a French drain need?
About 1% — roughly 1 inch of fall every 8 feet — pitched toward the outlet. Water barely flows on the flat: a level trench is an underground pond, not a drain. Check the grade with a string line or laser while you dig, not after it's filled.
Should I use 4-inch or 6-inch pipe?
4-inch perforated pipe is the residential standard. It handles most yards. Step up to 6-inch for very long runs or heavy flow — the calculator asks which size you're running before it counts sections, and on runs past 300 ft it nudges you toward 6-inch and a cleanout or two.
How much landscape fabric do I need?
More than the trench's footprint — the fabric wraps the gravel like a burrito. Down one side, across the bottom, up the other, and folded over the top: per foot of trench that's the width plus twice the depth, so (1 + 2 × 1.5) × 50 ft = 200 sq ft for the standard trench — 2 rolls of the common 3 × 50 ft size. Use non-woven drainage fabric, never plastic weed barrier; it clogs.
Does the gravel amount leave room for the pipe?
No — the calculator orders the full trench volume as gravel, on purpose. The pipe takes up so little room beside the gravel bed that field practice just fills the trench. Ordering less to make room for the pipe leaves you short at the far end.
How much extra should I add for waste?
The calculator starts at 0%, and +10% is the usual chip to tap. The percentage applies to all three materials — gravel, pipe length and fabric — before rounding up to whole pipe sections and fabric rolls. At +10% the 50-ft example comes to 3.06 yd³ of gravel, 6 pipe sections and 2 rolls of fabric.