Gutter Calculator
How much eave?
Diagram: what the measurements mean
Total feet of roof edge getting gutter — add up all the runs.
Walk it with a tape, or pace it off and add 10%.
Stories & downspouts
Taller drops need longer downspouts — we preset a sensible count.
Pick 1 or 2 stories.
We suggest 1 per ~35 ft of gutter — adjust for corners and valleys.
Your gutter count
Waste allowance Starts at 0% — tap to add a cushion for cuts & miters.
FEET OF GUTTER
–
- Gutter LF
- –
- Downspouts
- –
- Downspout LF
- –
- Elbows
- –
- Hangers
- –
💡 Pro field tips
🧰 Tools you'll need
Tap to check off as you load up.
Est. project cost (optional)
File this estimate under a job name or PO to track what to order. Leave blank to file under "General".
Copied to clipboard ✓
How the math works
Gutters answer four questions: how many feet of trough, how many downspouts drain it, which way water flows, and what holds it up. Miss one and you get waterfalls over the edge or standing water breeding mosquitoes. Here's the full picture.
Linear feet of gutter
Gutters run the eaves — the roof's lower edges where water sheds:
Gutter length = Total eave length
A 40-ft house: 40 ft per side = 80 ft total. Measure the eave, not the wall — overhang adds a foot or more per side. In 10-ft sections (gutter is sold that way — the calculator totals footage, not a section count): 80 ÷ 10 = 8 sections, plus end caps and connectors.
Downspouts: the drains
One downspout per 30–40 ft of gutter — a single spout can't swallow a 40-ft roof's worth of rain:
Downspouts = Gutter length ÷ 35, rounded UP (min. 1 per run)
Two 40-ft runs: 40 ÷ 35 = 1.14 → 2 per side, 4 total. Each needs elbows top and bottom plus vertical pipe ≈ eave height + 2 ft.
Slope: water flows downhill
Gutters pitch toward the downspout — ¼ inch per 10 feet:
Drop = (Run ÷ 10) × 0.25 in
40 ft → 1 inch of drop. Barely visible, but it's the difference between draining and holding a permanent puddle. Runs over 40 ft: pitch from the middle to downspouts at both ends.
Hangers: what holds it up
Water-filled gutter weighs ~5 lbs per foot. Hangers every 24 inches (16–18 in snow country) prevent sagging — sag creates low spots, low spots hold water, standing water rots fascia:
Hangers = Gutter inches ÷ 24, rounded UP
80 ft = 960 in ÷ 24 = 40 hangers.
Waste factor
Only a little: sections are modular and offcuts get reused. This calculator starts at 0% waste — add a small cushion like 5% with the waste buttons if you want one. The real insurance is one spare elbow and connector — cheap, and a cracked elbow at 4 PM Saturday is a special misery.
Worked example: 40-ft house, both sides
- 8 ten-ft sections; 4 downspouts; 40 hangers; 1-in drop per 40-ft run
Most Asked Questions
How much slope does a gutter need?
¼ inch of drop for every 10 feet, aimed at the downspout. A 40-ft run falls 1 full inch end to end — and past 40 ft, pitch from the middle so each half drains to its own downspout.
How many downspouts does my house need?
One downspout for every 35 feet of gutter. That's the middle of the 30-to-40-ft range — always at least one per run, always round up, and add one where a valley dumps extra water. The calculator pre-fills this count for you, elbows and pipe included.
Should I get 5-inch or 6-inch gutters?
5-inch K-style is the standard for most houses. Step up to 6-inch for a big or steep roof, or where heavy downpours are common — it moves more water and pairs with 3×4-inch downspouts. Size changes the trough, not the layout: every count from this calculator stays the same.
How far apart should gutter hangers be?
Every 24 inches. In snow country, tighten it to 16–18 inches. Here's why it matters: a gutter full of rain weighs about 5 pounds per foot, and the wide gaps are exactly where a run starts to sag.
How do I measure how much gutter my house needs?
Measure the eave, not the wall. The roof overhang adds a foot or more per side. Add up every run that's getting gutter and enter the total here — the waste starts at 0% — add what you want for cuts with the waste buttons — and the gutter itself comes in 10-ft sections (the calculator totals footage, not sections). No tape handy? Pace the runs off and add 10%.
Can I hang my gutters dead level so the line looks straight?
No — a level gutter holds water instead of draining it. Standing water breeds mosquitoes, adds constant weight that works hangers loose, and rots the fascia behind the trough. The real pitch is only about an inch over 40 ft, so a properly sloped gutter still looks straight from the ground.