Kipi Calculator SAND CALCULATOR by Kipi Calculator
🌐 Español

Sand Calculator

    What kind of sand?

    Pick the type — each one weighs a different amount per cubic foot.

    How much do you need?

    Measure an area and a depth — or type in a volume you already know.

    Typical depths: 1 in for paver bedding and jointing, 2–4 in for sandboxes, leveling, and under-pool pads.

    Waste allowance — extra for spills, uneven grade & over-dig

    Your sand order

    Sand needed — by weight

    – tons

    Cubic yards
    –
    Cubic feet
    –
    50-lb bags
    –
    60-lb bags
    –

      💡 Pro field tips

        🧰 Tools you'll need

        Tap to check off as you load up.

        Est. project cost (optional)

        File this estimate under a job name or PO to track what to order. Leave blank to file under "General".

        Assumptions & limits: This uses planning densities — play sand and dry all-purpose sand at about 100 lb per cubic foot, masonry/construction sand at about 105, and wet sand at about 120. Real sand varies with moisture and grain size, so an actual load can run a few percent over or under these numbers. Bag counts are for dry bagged sand and are rounded up to whole bags — a rain-soaked bag weighs more and covers less. Ordering 5–10% extra is standard to cover compaction, spills, and uneven ground underneath. This figures the sand only — base gravel, geotextile fabric, and edging are separate.

        How the math works

        Sand is measured by space but sold by weight (bulk) or by the bag. The calculation bridges the two: figure the space first, then turn it into pounds with the sand's density.

        Volume: length × width × depth

        Multiply length by width for square feet, then multiply by the depth in feet (inches ÷ 12) for cubic feet. Divide by 27 for cubic yards:

        Cubic feet = Length (ft) × Width (ft) × Depth (in ÷ 12)

        Weight: density does the work

        Dry sand weighs about 100 lb per cubic foot. Masonry sand runs a little heavier (~105), and wet sand can hit ~120 because the water between the grains adds up fast:

        Tons = Cubic feet × Density (lb/ft³) ÷ 2,000

        Bags: divide the pounds, round up

        Bagged sand comes in 50-lb and 60-lb bags (play sand is often 50 lb). Divide the total weight by the bag size and always round up — you can't buy a third of a bag, and running one bag short means another trip.

        Worked example: 10 × 10 sandbox area, 2" of play sand

        • Volume: 10 × 10 × (2 ÷ 12) = 16.67 ft³ = 0.62 yd³
        • Weight: 16.67 × 100 = 1,667 lb = 0.83 tons
        • 50-lb bags: 1,667 ÷ 50 = 33.3 → 34 bags
        • 60-lb bags: 1,667 ÷ 60 = 27.8 → 28 bags

        Need the gravel or base layer underneath first? Run the Gravel Calculator for that layer, then add the two orders together.

        Worked example

        A 15 × 15 ft play area getting 3 inches of play sand — deep enough to cushion, using this calculator's numbers for play sand (about 100 lb/ft³):

        • Volume: 15 × 15 × (3 ÷ 12) = 56.25 ft³ = 2.08 yd³
        • Weight: 56.25 × 100 = 5,625 lb = 2.81 tons
        • In 50-lb bags: 5,625 ÷ 50 = 112.5 → 113 bags
        • In 60-lb bags: 5,625 ÷ 60 = 93.75 → 94 bags

        At 113 bags, this job is the perfect example of the bulk rule below — a single bulk delivery of about 3 tons beats a hundred trips down the bag aisle.

        On a real job

        • Past 30 or 40 bags, buy bulk. Bagged sand is convenience-priced. A bulk ton delivered usually costs less than the same weight in bags — and somebody else does the carrying.
        • Wet sand is heavy sand. Bulk is sold by weight, and sand that's been rained on carries real water in the load. When you can, take delivery on a dry stretch — you're paying for sand, not weather.
        • Depth settles — plan a top-up. Play sand compacts under feet and migrates out on shoes. Expect to lose some depth in the first month or two; a small top-up run keeps you at the depth you planned.
        • Keep sand off bare dirt. Landscape fabric under the area stops sand and soil mixing — without it, your 3 inches quietly becomes 2 inches of sand-mud.
        • Match the sand to the job. Play sand is fine, round-grained — good for play areas, poor for paver bedding, where you want coarse, angular concrete sand that locks together. The calculator's density choices exist because "sand" is three different materials wearing one name.

        Most Asked Questions

        How many 50-lb bags of sand do I need for a 10×10 area at 2 inches deep?

        34 bags. The area holds 16.67 cubic feet (0.62 yd³); play sand at 100 lb per cubic foot weighs 1,667 lb, and 1,667 ÷ 50 = 33.3 — round up to 34. In 60-lb bags it's 28.

        How much does a cubic yard of sand weigh?

        About 2,700 lb — roughly 1.35 tons — dry. That's 27 cubic feet × 100 lb per cubic foot. Wet sand can top 3,200 lb per yard, which is why a soaked yard covers less than the scale ticket suggests.

        How much area does a ton of sand cover?

        About 240 sq ft at 1 inch deep. A ton of dry sand is about 20 cubic feet: at 2 inches it covers about 120 sq ft, at 4 inches about 60. The shortcut: coverage = 240 ÷ depth in inches.

        What is the difference between play sand and masonry sand?

        Play sand is washed, fine, and round-grained — soft for kids and free-draining. Masonry sand is also washed and fine, graded for smooth mortar; all-purpose construction sand is coarser and cheaper, fine for fill and bedding. Their weights are close: about 100 lb per cubic foot for play and all-purpose, 105 for masonry.

        Should I buy sand in bags or in bulk?

        Under about half a ton, bags are simpler; at a ton or more, bulk wins. Bags skip the delivery fee and spread the trips out. Bulk by the yard or ton is far cheaper per pound, but you need a truck, trailer, or delivery and a spot to dump it. Keep bagged sand under cover — a wet 50-lb bag can weigh 60 lb or more and clumps when you spread it.

        How much extra sand should I order?

        Plan on about 10% extra. Sand compacts, spills, and disappears into uneven ground — this calculator's waste selector starts at 0% — tap 10% and it pads the tonnage it tells you to order. Bags are figured exact, so round up a bag or two there as well.

        Next calculation

        One job usually leads to the next number. Common next steps from here:

        Embed this calculator on your site

        Run a DIY, contractor, or supplier site? Put this sand calculator right on your page, free. Copy the code and paste it where you want it — your visitors get the numbers without leaving your site.

        Free to use. The small “Powered by Kipi Calculator” line at the bottom of the calculator stays on — that’s all we ask.

        Popular lookups

        10×10 area · 10×12 area · 12×12 area · 10×20 area · All charts